Skip to content
Refinish Wraps Architectural Film Refinish Wraps Architectural Film
  1. Home
  2. Elevator cabs and landings

Elevator cabs and landings

Everyone in the building rides the elevator, and most cabs show it. We refinish cab walls, cab doors and trim, and the hall doors and frames on every floor, one elevator at a time.

Elevator cab with light oak wall panels
Cab walls refinished in light oak

Same elevator.
A brand new look.

Scuffed cherry cab panels became light oak. A scratched stainless landing became walnut. Nothing was replaced, and the buttons, handrails, ceiling and floor stayed exactly as they were.

After: elevator cab interior refinished Before: elevator cab interior
BeforeAfter
Inside the cab, cherry to light oakDrag the handle
  • 1 at a timeIn buildings with two or more elevators, the rest stay in service.
  • 1 to 2 daysTypical time for a cab, depending on size and trim.
  • Every floorLandings are often the bigger job. A 20 story tower with 3 cars has 60 of them.

Inside the cab

Cab walls are usually stainless, plastic laminate or wood panels that have been scratched, keyed and leaned on for years. Film goes right over them. We also wrap the inside face of the cab doors, the front return and any trim, and we work around the handrails, the car operating panel and the lighting.

If a panel has to come off, or anything touches the controls, we bring in your elevator contractor. Most of the time it isn't needed.

  • Wrapped: wall panels, cab door interior, front return, trim and reveals
  • Left alone: buttons and car panel, handrails, ceiling and lights, floor

The landings

The hall side of the elevator is the first thing people see on every floor. Painted frames chip and stainless doors get scratched by carts and luggage. We wrap the door panels, frame and surround, and leave the call station and sill alone.

Doing landings and cabs together gives every floor the same look, and it's usually cheaper than doing them in separate phases.

Elevator landing on a typical floor Hall side of an elevator showing the frame and surround, the two door panels, the hall call station and sill. Frame and surroundWrapped, shown in bronze Hall door panelsBoth panels, hall side Call stationStays as is SillNever wrapped
Hall side of a two panel elevator entrance.

Elevator finishes that work

Metals are the default, but wood and stone looks make a cab feel like part of the lobby.

3M DI-NOC ME-1434, brushed stainless architectural film sample
Brushed stainless3M ME-1434 · Clean, classic
3M DI-NOC ME-1997, brushed champagne architectural film sample
Brushed champagne3M ME-1997 · Warm, upscale
3M DI-NOC ME-1685, black steel architectural film sample
Black steel3M ME-1685 · Modern
3M DI-NOC FW-1801, walnut architectural film sample
Walnut3M FW-1801 · Matches wood lobbies
3M DI-NOC ST-1831, white marble architectural film sample
White marble3M ST-1831 · Bright, high end

Elevator questions

How long is an elevator out of service?

It depends on the size of the cab and how much trim there is. Most cabs are done in a day or two. In buildings with more than one elevator we do one at a time so service never stops.

Do you need the elevator company there?

Usually not for wrapping cab walls and doors in place. If panels have to come off, or anything touches the car controls, we coordinate with your elevator contractor.

Can you wrap stainless steel?

Yes. Scratched stainless cab walls and hall doors are some of the most common jobs we see. We can go over it with a fresh brushed metal, a bronze, a wood grain or a stone look.

What about the buttons and handrails?

Car operating panels, hall call buttons, handrails and ceiling fixtures stay as they are. We wrap around them.

Get an elevator priced.

Tell us how many cars and how many floors. Send a photo of each cab wall, the inside of the doors, and one landing. We'll come back with a ballpark within one business day.

(561) 802-1148

Text or call. Photos get you the fastest answer.

Call now